DESCRIPTION

Plugs into a blank slot below the heater controls of a Golf 3 instead of a cap and holds one 52 mm gauge flush.

For the VW Golf 3 (1H), including GTI, VR6 and Vento: the pod plugs into an accessory slot below the heater and fan controls instead of a blank cap and holds one 52 mm gauge flush – e.g. oil temperature on the VR6 or boost on the TDI.

  • A hollow plug with crush ribs clamps in the slot like the original cap. Nothing is drilled.
  • The gauge sits flush in the pod, held by crush ribs without screws.
  • The cable runs through the plug behind the console.
  • Variants for 45, 50 and 55 mm gauge depth.
  • Gauge sizes: 38 / 39.7 / 41 / 45 / 52 / 60 / 66.7 mm as separate variants, each with a matching tolerance test ring. 60 and 66.7 mm need a taller and wider block (68 × 74 or 76 × 82 instead of 60 × 60 mm) that can reach the heater controls: check the surroundings; these two are file-only for now.
  • Prints face-down on the bed: smooth visible side, no supports.

The slot is only 27 mm tall, so the pod sits in front of the console and protrudes by the gauge depth.

Designed for
  • VW Golf 3, 1H, 1991–1997
    • Trims: GTI, VR6, TDI, GT, Vento, Variant
    • Slot size taken from the original part (Printables 1080985, CC BY). Golf 3 Cabrio (1E) with the same dashboard not confirmed. Passenger airbag standard from 1995 – in the dashboard top, not here.
Variants (all included)
  • Gauge up to 45 mm deep
  • Gauge up to 50 mm deep
  • Gauge up to 55 mm deep
  • 38 mm gauge (up to 50 mm deep)
  • 39.7 mm gauge (up to 50 mm deep)
  • 41 mm gauge (up to 50 mm deep)
  • 45 mm gauge (up to 50 mm deep)
  • 60 mm gauge (up to 50 mm deep)
  • 66.7 mm gauge (up to 50 mm deep)

Gauge bore: 52.79 mm (52 mm gauges, +0.4 mm clearance).

Included
  • STL, 3MF and STEP for every variant
  • 52 mm tolerance test ring – print it first
  • README with print settings and installation (EN/DE)
Safety

The slot sits below the heater controls, clear of the airbag zones. The pod must not obstruct the gear lever or heater controls – check in every gear.

Fit

File the crush ribs if needed; too loose: felt tape on the plug. Bore +0.4 mm, check with the test ring. If the fit loosens after strong heat: build up the ribs with thin tape or felt.Dimensions taken from published sources: Printables 1080985 by zazaw1zard (CC BY 4.0); only measurements were used, no geometry. Not yet tested on the vehicle.

FAQ

Which gauge sizes are there? 38 / 39.7 / 41 / 45 / 52 / 60 / 66.7 mm. In inches: 38 mm / 1-1/2 in, 41 mm / 1-5/8 in (panel hole of Bosch mini gauges), 52 mm / 2-1/16 in, 60 mm / 2-3/8 in, 66.7 mm / 2-5/8 in. 39.7 mm is the panel hole Auto Meter gives for its small gauges according to dealer data. Electrical senders only: never run a fuel or oil pressure line into the cabin. Print the test ring for your size first; for 38/39.7/41/45 it also has a ring below the nominal size. 60 and 66.7 mm need a taller and wider block (68 × 74 or 76 × 82 instead of 60 × 60 mm) that can reach the heater controls: check the surroundings; these two are file-only for now.

How it's made

Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes. Renders are made from the CAD in Blender.

License

Personal use only. Please do not resell the files or printed parts.Dimensions from published sources, not yet tested on the vehicle.Not an original part, no affiliation with the vehicle manufacturer (VW). Brand and model names are used only to indicate the intended vehicle.

Deutsch: Steckt statt einer Blindkappe im Steckplatz unter der Heizungsbedienung des Golf 3 und hält ein 52-mm-Instrument bündig.Alle Varianten als STL/3MF/STEP, Testring und Anleitung DE/EN enthalten. Private Nutzung, kein Weiterverkauf von Dateien oder Drucken.

REVIEWS & COMMENTS

See what other buyers think about this model - real feedback on quality,
accuracy, and usability.
There are no reviews or comments yet. Please be the first one to write it.
NEW
Recently added to CGTrader - explore one of the latest models on the marketplace.

Gauge pod for VW Golf 3 Vento 1991-1997 52mm 60mm 67mm Free 3D print model

Free
Royalty Free License (no AI)

Free for personal and commercial use

Like this model to show appreciation to the designer.
See how many times this model was viewed.
Share this model to support the designer and boost their visibility.
File formats
STL
Stereolithography | 2 files<br />File Size: 1.93 MB
3MF
3D Manufacturing File | 2 files<br />File Size: 3.29 MB
STP
STEP | 2 files<br />File Size: 3.29 MB
Provided by designer
Information and details shared directly by the model's designer.
3D printing
Indicates whether the designer marked this model as suitable for 3D printing.
Model is prepared for 3D printing
The designer indicates this model is prepared for physical 3D printing and includes printable file formats.
Pre-supported or supports are not needed
Units
Publish date
Model ID
Chat