DESCRIPTION

Plugs into the blank where 4x4 Dusters have the drive mode switch and holds one 52 mm gauge.

For the Dacia Duster II (HM) with front-wheel drive (2018–2024), also the Renault Duster 2G: 2WD cars have a blank plug behind the gear lever instead of the 4x4 mode switch. The pod plugs in there and holds one 52 mm gauge – often boost on the TCe.

  • A round hollow stem with crush ribs clamps in the opening; the cable runs through it into the console. Nothing is drilled.
  • Tilt 45 or 60° toward the driver; round, so turn it toward the driver when fitting.
  • An M3 set screw secures the gauge.
  • Gauge sizes: 38 / 39.7 / 41 / 45 / 52 / 60 / 66.7 mm as separate variants, each with a matching tolerance test ring. Stem and base plate stay the same for all sizes. 66.7 mm: cup about Ø 72 mm outside (75 with the screw boss) and taller than at 52 mm – file only for now, check the surroundings (gear lever in every gear, handbrake, controls).
  • Prints without supports.

Only for cars without 4x4 (those have the mode switch there).

Designed for
  • Dacia Duster II, HM, 2018–2024
    • Trims: 2WD (front-wheel drive), TCe, dCi / Blue dCi, Renault Duster 2G (2021+), not 4x4
    • 2WD with blank plug only. Opening size taken from a dummy cup (Printables 890402, CC0), our part not yet tested in a car; Renault Duster 2G from 2021 according to reference 973640. Centre console behind the gear lever, no airbag there.
Variants (all included)
  • Tilt 45° · 38 mm gauge
  • Tilt 60° · 38 mm gauge
  • Tilt 45° · 39.7 mm gauge
  • Tilt 60° · 39.7 mm gauge
  • Tilt 45° · 41 mm gauge
  • Tilt 60° · 41 mm gauge
  • Tilt 45° · 45 mm gauge
  • Tilt 60° · 45 mm gauge
  • Tilt 45° · 52 mm gauge
  • Tilt 60° · 52 mm gauge
  • Tilt 45° · 60 mm gauge
  • Tilt 60° · 60 mm gauge
  • Tilt 45° · 66.7 mm gauge
  • Tilt 60° · 66.7 mm gauge

Gauge bore: 52.79 mm (52 mm gauges, +0.4 mm clearance).

Included
  • STL, 3MF and STEP for every variant
  • 52 mm tolerance test ring – print it first
  • README with print settings and installation (EN/DE)
Safety

The position is behind the gear lever. The pod must not obstruct the gear lever, handbrake or cup holder – after fitting, check in every gear and with the handbrake pulled.

Hardware (not included)
  • 1 × M3 set screw or self-tapping M3 screw, 8–10 mm
Fit

File the crush ribs if needed; too loose: felt tape on the stem. Bore +0.4 mm, check with the test ring. If the fit loosens after strong heat: build up the ribs with thin tape or felt.

FAQ

Which gauge sizes are there? 38 / 39.7 / 41 / 45 / 52 / 60 / 66.7 mm. In inches: 38 mm / 1-1/2 in, 41 mm / 1-5/8 in (panel hole of Bosch mini gauges), 52 mm / 2-1/16 in, 60 mm / 2-3/8 in, 66.7 mm / 2-5/8 in. 39.7 mm is the panel hole Auto Meter gives for its small gauges according to dealer data. Electrical senders only: never run a fuel or oil pressure line into the cabin. Print the test ring for your size first; for 38/39.7/41/45 it also has a ring below the nominal size. Stem and base plate stay the same for all sizes. 66.7 mm: cup about Ø 72 mm outside (75 with the screw boss) and taller than at 52 mm – file only for now, check the surroundings (gear lever in every gear, handbrake, controls).Does a 60 mm gauge fit? Yes, in the “60 mm” variants: 60.4 mm bore for gauges with a 60 mm housing (e.g. Defi 60). The cup is then Ø 65 mm outside, 7.6 mm wider than for 52 mm – after fitting, check that levers and controls stay clear.

How it's made

Parametric CAD (build123d, Python), exact solids. The CAD code was written with an AI assistant and checked by us; no AI-generated meshes. Renders are made from the CAD in Blender.

License

Personal use only. Please do not resell the files or printed parts.Dimensions from published sources, not yet tested on the vehicle.Not an original part, no affiliation with the vehicle manufacturer (Dacia). Brand and model names are used only to indicate the intended vehicle.

Deutsch: Steckt bei 2WD-Dustern im Blindstopfen-Platz des 4x4-Schalters in der Mittelkonsole und hält ein 52-mm-Instrument.Alle Varianten als STL/3MF/STEP, Testring und Anleitung DE/EN enthalten. Private Nutzung, kein Weiterverkauf von Dateien oder Drucken.

REVIEWS & COMMENTS

See what other buyers think about this model - real feedback on quality,
accuracy, and usability.
There are no reviews or comments yet. Please be the first one to write it.
NEW
Recently added to CGTrader - explore one of the latest models on the marketplace.

52mm gauge pod for Dacia Duster II 2WD 2018-2024 3D print model

Royalty Free License
One-time purchaseRoyalty-free
$6.99
  • Yours forever — royalty-free license
  • All 3 file formats included
  • Instant download after purchase
Like this model to show appreciation to the designer.
See how many times this model was viewed.
Share this model to support the designer and boost their visibility.
File formats
STL
Stereolithography | 2 files<br />File Size: 9.13 MB
3MF
3D Manufacturing File | 2 files<br />File Size: 17.6 MB
STP
STEP | 2 files<br />File Size: 17.6 MB
Provided by designer
Information and details shared directly by the model's designer.
3D printing
Indicates whether the designer marked this model as suitable for 3D printing.
Model is prepared for 3D printing
The designer indicates this model is prepared for physical 3D printing and includes printable file formats.
Pre-supported or supports are not needed
Units
Publish date
Model ID
Chat