Snowstock Delta Bot Free 3D print model

I wanted to build a wolfstock style delta-bot, using Makerslide linear slides. But, I wanted to run the belt through the inside of the Makerslide for a cleaner look.
This is still very much a work in progress, I'm currently working on completing the design and building the printer.
I'm posting a build log on my blog:
http://andy-projects.blogspot.com/2013/12/delta-bot-build.html
http://andy-projects.blogspot.com/2014/01/delta-bot-build-part-2-belt-tensioners.html
http://andy-projects.blogspot.com/2014/01/delta-bot-build-part-3-effector-rods.html
http://andy-projects.blogspot.com/2014/04/delta-bot-build-cooling-fan-magnetic.html

1.1.2014 Update:
-added belt clip, bolt to back of makerslide carriage
-added belt tensioner to idler bracket
-added tensioner arm
1.15.2014 Update:
-Added carriage mount for rod ends
-Added platform (intended for budaschnozzle but lots of mounting holes for anything)
-added rod sleeve (for reinforcing end of carbon rods)
1.18.2014 Update:
-updated platform and rod carriage mount to improve fit with traxxas rod ends
1.19.2014 Update:
-updated platform and rod carriage mounts to allow better clamping of traxxas rod ends including variability in rod end center width
3.19.2014 Update:
-added shroud for 40mm fan
-added bowden tube mount for Budaschnozzle
-added 5mm spacer for Budaschnozzle
-added platform for magnetic bearings
-added carriage mount for magnetic bearings
4.03.2014 Update:
-added M5 threaded rod end caps for magnetic bearings
9.8.2014 Update:
-added upper and lower braces to stiffen structure.

Components required: (list in progress)
Makerslide Components
-3x 2040 size Makerslide, my build is using 895mm length (allowing 2x pieces cut from 1800mm sections of Makerslide)
-3x carriage plate 25200-01 www.inventables.com
-6x Dual Bearing V-Wheel kike 25203-02 www.inventables.com
-3x Eccentric spacer 25195-02 www.inventables.com
-3x Smooth Idler Wheel Kit 25197-02 www.inventables.com
-9x M5 lock nuts (v-wheels)
-9x M5x20 SHCS (v-wheels)
Motion Control
-3x 16T GT2 Pulleys
-3x NEMA 17 steppers
-3x GT2 belt, 198cm long each (approximately)
Aluminum Extrusions
-3x 1square 8020 x 275mm (upper assembly)
-6x 1 square 8020 x 250mm (lower assembly)
Fasteners
-3x M5x25mm SHCS (idler wheel mounts, 30mm will also work)
-3x M5 nuts (idler wheel mounts)
-6x M5x20mm SHCS (idler tensioner screws)
-6x M5 nuts (idler tensioner nuts)
-60x M5x10mm SHCS
-60x M5 T-slot nuts
-12x M5 x 20mm SHCS for mounting Makerslide
-12x M3 x 12mm SHCS (stepper mounts)
-12x M3 washers (stepper mounts)
-36x M6x20mm SHCS (optional, end screws for 8020 to corners)
Connector Rods
-8.5mm OD x 7.25mm ID carbon rods
-Traxxas 5525 rod ends (traditional rod end choice)
-10mm spherical rare earth magnets + 24 5mm x 10mm SHCS with head machined (magnetic bearings)